Brand: LDO Motors

LDO Motors

Showing all 13 results

Quick View

LDO Galileo 2 Kit for Clockwork 2 (G2E)
$109.90
One of the most expected project of 2022, the Orbiter v2.0
Add to cart Details Buy Now
Quick View

LDO Heat Insert Tool Kit (includes 50pc M3x5x4 heat set inserts)
$14.90
Install your M3 threaded heat set inserts with ease and precision with this insert tool kit from LDO motors. Includes brass soldering iron tip and 50 M3x5x4 heat set inserts, suitable for Voron builds.
Add to cart Details Buy Now
Out of Stock
Sold Out
Quick View

LDO High Power 1.8 Degree StepperMotor – LDO-42STH48-2804AH
$54.90
This is a super big boy, made for the highest speed of speedy applications. This motor comes with a 1 meter wire terminated with a 4 pin JST-XH connector. We carry these in AH (high temp). Ideal for use as XY motors on a CoreXY printer.
Read more Details

Quick View

LDO High Speed 0.9 Degree StepperMotor – LDO-42STH48-2004MAH(VRN)
$45.90
This is a high quality, high speed and high torque 0.9° stepper motor. Ideal for use as XY motors on a CoreXY printer.
Add to cart Details Buy Now

Quick View

LDO High Speed 1.8 Degree StepperMotor – LDO-42STH48-2504AC
$39.90
This is a high quality, high speed and high torque stepper motor. Ideal for use as XY motors on a CoreXY printer.
Add to cart Details Buy Now

Quick View

LDO Nema 17 COOL POWER Extruder Motor 1.8 LDO-42STH40-1004ASR
$39.90
New motor design. Extruder Motor stays much cooler during printing. NOT suited for x and y axis. COOL POWER stepper motor. Compatible with PRUSA MK3 extruder motor.
Add to cart Details Buy Now

Quick View

LDO Nema 17 Pancake 1.8 degree Stepper Motor 25mm – LDO-42STH25-1004AC
$39.90
Nema 17 High resolution 1.8° pancake stepper motor. Perfect fit for BMG / Prusa extruder upgrades.
Add to cart Details Buy Now

Quick View

LDO Orbiter V2.0 Extruder
$146.90
One of the most expected project of 2022, the Orbiter v2.0
Add to cart Details Buy Now

Quick View

LDO Pancake Stepper Motor LDO-36STH20-1004AHG (Voron Clockwork 2)
$42.90
LDO 36mm Stepper Motor for your Voron Extruder. This is the pancake motor used on the LDO orbiter / Galileo, V01 mini-afterburner, and Stealthburner.
Add to cart Details Buy Now

Quick View

LDO Pancake Stepper Motor LDO-42STH20-1004ASH(VRN) (Afterburner)
$37.90
LDO 40mm Stepper Motor for your Voron Extruder. This is the stepper motor used on the Afterburner.
Add to cart Details Buy Now

Quick View

LDO Smart Orbiter v3.0
$239.90
This Smart Orbiter v3.0 manufactured by LDO Motors is an innovative all in one dual drive extruder / hot end tool head assembly. The main mission of this design is the integration of the well proven Orbiter v2 concept into a lightweight all in one smart extruder.
The Orbiter v3.0 was designed by Dr. Lorincz Robert, for more information visit https://www.orbiterprojects.com/so3/.
Add to cart Details Buy Now

Quick View

LDO V1 Z Motor Triple (V1ZMKT3) Teflon Coated for Trident
$199.90 – $269.90
Rated 5.00 out of 5
High quality stepper motor for the z- axis with integrated lead screw kit for LDO Trident 250/300 Cube or Standard Voron Trident Builds. Kit of 3.
Select options This product has multiple variants. The options may be chosen on the product page Details

Quick View

Voron V2.4 Motor Kit by LDO Motors (Clockwork 2 updated)
$239.90
This is a complete motor set for the Voron 2.4 by LDO motors. These are great motors, and include Voron branding.
Add to cart Details Buy Now

Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less

Andrew Jackson

5

I was directed to 3D... Read More
I was directed to 3DEA by a work colleague as I was new to 3D printing and they were right about them. Great quality PLA (and many other types), awesome range of colours and great pricing. I've bought 4 different rolls so far and they have all been great, no clogging and brilliant print quality. Read Less

Greedo Twerp

5

I was looking for a ... Read More
I was looking for a colour similar to the primer red seen on German WW2 heavy vehicles. Wanted to print a 1/4 scale model of a Tiger tank 88mm muzzle brake. Ordered the 3DEA "Brick Red" PLA which is a very good match. Never used prior and pleased to report printed faultlessly once I knocked the temp down to 200 degrees on my Kingroon KP3S. Printed at 0.10mm layer height, no stringing issues at all. Very happy customer. Already planning the next order, highly recommended. Read Less

Write a review!

Brand: LDO Motors

LDO Galileo 2 Kit for Clockwork 2 (G2E)

LDO Heat Insert Tool Kit (includes 50pc M3x5x4 heat set inserts)

LDO High Power 1.8 Degree StepperMotor – LDO-42STH48-2804AH

LDO High Speed 0.9 Degree StepperMotor – LDO-42STH48-2004MAH(VRN)

LDO High Speed 1.8 Degree StepperMotor – LDO-42STH48-2504AC

LDO Nema 17 COOL POWER Extruder Motor 1.8 LDO-42STH40-1004ASR

LDO Nema 17 Pancake 1.8 degree Stepper Motor 25mm – LDO-42STH25-1004AC

LDO Orbiter V2.0 Extruder

LDO Pancake Stepper Motor LDO-36STH20-1004AHG (Voron Clockwork 2)

LDO Pancake Stepper Motor LDO-42STH20-1004ASH(VRN) (Afterburner)

LDO Smart Orbiter v3.0

LDO V1 Z Motor Triple (V1ZMKT3) Teflon Coated for Trident

Voron V2.4 Motor Kit by LDO Motors (Clockwork 2 updated)

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA