Category: Extruders

Name: 3DEA
Address: Keith Hay Court, Silverdale, Auckland, 0932
Rating: 4.7

Extruders

Showing all 10 results

1M/2M two-phase XH2.54 4pin to 6pin Terminal Motor Connector Cable for Nema
$5.90 – $7.50
1M/2M Four-lead motor connector XH2.54 white terminal 4pin-6pin
Select options This product has multiple variants. The options may be chosen on the product page Details
Capricorn Bowden PTFE Tube – Creality
$19.90 – $39.90
Capricorn Premium bowden Tubing is enhanced with a proprietary blend of high performance additives.
Select options This product has multiple variants. The options may be chosen on the product page Details
CREALITY Red Metal Dual Gear Extruder – Ender 3 Series and CR-10 series
$32.90
An all metal upgrade kit for the Creality Ender extruder
Add to cart Details Buy Now
CREALITY Red Metal Extruder Upgrade Kit
$19.90
An all metal upgrade kit for the Creality Ender extruder
Select options This product has multiple variants. The options may be chosen on the product page Details
Dual Drive extruder – Cloned BMG Extruder CR10 1.75mm
$39.90 – $59.90
Dual Drive Extruder for high performance – Cloned BMB
Select options This product has multiple variants. The options may be chosen on the product page Details
LDO Galileo 2 Kit for Clockwork 2 (G2E)
$109.90
One of the most expected project of 2022, the Orbiter v2.0
Add to cart Details Buy Now
LDO Orbiter V2.0 Extruder
$146.90
One of the most expected project of 2022, the Orbiter v2.0
Add to cart Details Buy Now
LDO Smart Orbiter v3.0
$239.90
This Smart Orbiter v3.0 manufactured by LDO Motors is an innovative all in one dual drive extruder / hot end tool head assembly. The main mission of this design is the integration of the well proven Orbiter v2 concept into a lightweight all in one smart extruder.
The Orbiter v3.0 was designed by Dr. Lorincz Robert, for more information visit https://www.orbiterprojects.com/so3/.
Add to cart Details Buy Now
Phaetus APUS Extruder
$149.90
A 155g light weight all metal design with a Nema 14 stepper motor, gives the APUS extruder a perfect balance of rigidity and weight. The aluminium frame improves the heat dissipation of the Nema 14 stepper motor
Add to cart Details Buy Now
PTFE Tube / Teflon Tube
$4.90
Rated 5.00 out of 5
PTFE Tube / Teflon Tube
Select options This product has multiple variants. The options may be chosen on the product page Details

Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less
Andrew Jackson

5

I was directed to 3D... Read More
I was directed to 3DEA by a work colleague as I was new to 3D printing and they were right about them. Great quality PLA (and many other types), awesome range of colours and great pricing. I've bought 4 different rolls so far and they have all been great, no clogging and brilliant print quality. Read Less
Greedo Twerp

5

I was looking for a ... Read More
I was looking for a colour similar to the primer red seen on German WW2 heavy vehicles. Wanted to print a 1/4 scale model of a Tiger tank 88mm muzzle brake. Ordered the 3DEA "Brick Red" PLA which is a very good match. Never used prior and pleased to report printed faultlessly once I knocked the temp down to 200 degrees on my Kingroon KP3S. Printed at 0.10mm layer height, no stringing issues at all. Very happy customer. Already planning the next order, highly recommended. Read Less