Tag: Voron

Showing all 13 results

Quick View

All Metal Ender-3 / CR10 / Voron High Temperature Hotend
$79.90
Rated 5.00 out of 5
All Metal High Temperature Hotend for Ender-3 / CR10 / Voron and others
Add to cart Details Buy Now
Quick View

Dragon Hotend Voron Edition ST/HF
$169.90 – $189.90
This is the Voron edition of the Dragon Hotend is the new generation of 3D printing launched by Phaetus which adopts a full metal kit and high temperature resistance up to 500℃.
Select options This product has multiple variants. The options may be chosen on the product page Details
Quick View

DropEffect XG Hotend by Phaetus
Original price was: $149.90.Current price is: $99.90.
The DropEffect XG hot end is the one of the most (if not the most) advanced hot ends on the market. Lightweight (40g), high temperature (300C), kinematic coupling (one handed nozzle changes!) and with an eXtreme temperature gradient means it’s also less prone to clogging.
Add to cart Details Buy Now
Out of Stock
Sold Out
Quick View

LDO High Power 1.8 Degree StepperMotor – LDO-42STH48-2804AH
$54.90
This is a super big boy, made for the highest speed of speedy applications. This motor comes with a 1 meter wire terminated with a 4 pin JST-XH connector. We carry these in AH (high temp). Ideal for use as XY motors on a CoreXY printer.
Read more Details

Quick View

LDO High Speed 0.9 Degree StepperMotor – LDO-42STH48-2004MAH(VRN)
$45.90
This is a high quality, high speed and high torque 0.9° stepper motor. Ideal for use as XY motors on a CoreXY printer.
Add to cart Details Buy Now

Quick View

LDO High Speed 1.8 Degree StepperMotor – LDO-42STH48-2504AC
$39.90
This is a high quality, high speed and high torque stepper motor. Ideal for use as XY motors on a CoreXY printer.
Add to cart Details Buy Now

Quick View

LDO Pancake Stepper Motor LDO-36STH20-1004AHG (Voron Clockwork 2)
$42.90
LDO 36mm Stepper Motor for your Voron Extruder. This is the pancake motor used on the LDO orbiter / Galileo, V01 mini-afterburner, and Stealthburner.
Add to cart Details Buy Now

Quick View

LDO Pancake Stepper Motor LDO-42STH20-1004ASH(VRN) (Afterburner)
$37.90
LDO 40mm Stepper Motor for your Voron Extruder. This is the stepper motor used on the Afterburner.
Add to cart Details Buy Now

Quick View

Voron Printed Parts Kits
$299.90 – $439.90
Voron Printed Parts Kits are printed to Voron specifications.
Select options This product has multiple variants. The options may be chosen on the product page Details

Quick View

Voron V2.4 Motor Kit by LDO Motors (Clockwork 2 updated)
$239.90
This is a complete motor set for the Voron 2.4 by LDO motors. These are great motors, and include Voron branding.
Add to cart Details Buy Now

Quick View

Voron V2.4 Motor Kit by LKD
Original price was: $189.90.Current price is: $149.90.
This is a complete motor set for the Voron 2.4 by LKD. These are great motors without expensive branding.
Add to cart Details Buy Now

Sale ends in
0 2 9
Days
0 1
Hours
3 6
Minus
4 6
Secs

On Sale
2/8 Sold
Quick View

Voron V2.4 R2 300mm Kit (LDO, NO PI)
Original price was: $1,699.00.Current price is: $1,190.00.
Voron 2.4 Corexy V2.4 R2 Version 3D Printer Kit with High Quality Parts 300*300mm DIY Kit
Add to cart Details Buy Now

Sale ends in
0 2 9
Days
0 1
Hours
3 6
Minus
4 6
Secs

Quick View

Voron V2.4 R2 350mm Kit (LDO, NO PI)
Original price was: $1,999.90.Current price is: $1,450.00.
Voron 2.4 Corexy V2.4 R2 Version 3D Printer Kit with High Quality Parts 350*350mm DIY Kit
Add to cart Details Buy Now

Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less

Andrew Jackson

5

I was directed to 3D... Read More
I was directed to 3DEA by a work colleague as I was new to 3D printing and they were right about them. Great quality PLA (and many other types), awesome range of colours and great pricing. I've bought 4 different rolls so far and they have all been great, no clogging and brilliant print quality. Read Less

Greedo Twerp

5

I was looking for a ... Read More
I was looking for a colour similar to the primer red seen on German WW2 heavy vehicles. Wanted to print a 1/4 scale model of a Tiger tank 88mm muzzle brake. Ordered the 3DEA "Brick Red" PLA which is a very good match. Never used prior and pleased to report printed faultlessly once I knocked the temp down to 200 degrees on my Kingroon KP3S. Printed at 0.10mm layer height, no stringing issues at all. Very happy customer. Already planning the next order, highly recommended. Read Less

Write a review!

Tag: Voron

All Metal Ender-3 / CR10 / Voron High Temperature Hotend

Dragon Hotend Voron Edition ST/HF

This is the Voron edition of the Dragon Hotend is the new generation of 3D printing launched by Phaetus which adopts a full metal kit and high temperature resistance up to 500℃.

DropEffect XG Hotend by Phaetus

LDO High Power 1.8 Degree StepperMotor – LDO-42STH48-2804AH

LDO High Speed 0.9 Degree StepperMotor – LDO-42STH48-2004MAH(VRN)

LDO High Speed 1.8 Degree StepperMotor – LDO-42STH48-2504AC

LDO Pancake Stepper Motor LDO-36STH20-1004AHG (Voron Clockwork 2)

LDO Pancake Stepper Motor LDO-42STH20-1004ASH(VRN) (Afterburner)

Voron Printed Parts Kits

Voron V2.4 Motor Kit by LDO Motors (Clockwork 2 updated)

Voron V2.4 Motor Kit by LKD

Voron V2.4 R2 300mm Kit (LDO, NO PI)

Voron V2.4 R2 350mm Kit (LDO, NO PI)

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA