JAMGHE 10K Water Washable

$59.90 – $64.90

JAMG HE Resin Water-Washable 10K is a precise material for printing at the highest resolution and great performance. The resin is easy to clean with water and is perfect to use for any type of industry. Ideal for general prototyping and printing dental models.

1kg - High Clear, Nebula/Deep Grey, Black, Clear, Grey, White

Very low shrinkage between 0.3% and 0.6%.

Fast curing time

JAMG HE Resin Water-Washable 10K is a precise material with the highest resolution of 10K and great performance. The resin is easy to clean with water and is perfect to use for any type of industry. Ideal for general prototyping and printing dental models.

highest resolution 12K – very precise with great performance
water-washable – printed models can be easily cleaned with water
low viscosity – 70-175mPa.s, high success printing rate in large size 3d printer, also works great in top-down resin printer
ideal for general prototyping and dental applications – can be used for dental orthodontic labs, as the water cleaning way saves and bring efficiently produced
works with 385 and 405nm wavelength
for LCD-type 3D Printers

Technical Specification

Volume: 1kg
Viscosity: 70-175 MPa.S
Density: 1.05-1.25 g/cm3
Tensile Strength: 31.44±10% MPa
Tensile Modulus: 741.03±10% MPa
Elongation at Break: 7.65±10%
Notched Impact Strength: 40.82±10% J/m
Surface Hardness: Shore 80-85D

Compatible with

Most LCD-type 3D Printers

Suitable for 2k, 4k, 6k, 8k, 10k and 12k resolution printers

Blind Gift

Unwrap the surprise in every bottle. You might find a USB driver, 5 paper funnels, or a pair of nitrile gloves, making your experience even more enjoyable.

Weight	1 kg
Dimensions	8 × 8 × 20 cm
Brand	Jamg He
Colour	High Clear, Nebula/Deep Grey, Black, Clear, Grey, White
Option	1kg

Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less
Andrew Jackson

5

I was directed to 3D... Read More
I was directed to 3DEA by a work colleague as I was new to 3D printing and they were right about them. Great quality PLA (and many other types), awesome range of colours and great pricing. I've bought 4 different rolls so far and they have all been great, no clogging and brilliant print quality. Read Less
Greedo Twerp

5

I was looking for a ... Read More
I was looking for a colour similar to the primer red seen on German WW2 heavy vehicles. Wanted to print a 1/4 scale model of a Tiger tank 88mm muzzle brake. Ordered the 3DEA "Brick Red" PLA which is a very good match. Never used prior and pleased to report printed faultlessly once I knocked the temp down to 200 degrees on my Kingroon KP3S. Printed at 0.10mm layer height, no stringing issues at all. Very happy customer. Already planning the next order, highly recommended. Read Less

Write a review!

JAMGHE 10K Water Washable

Technical Specification

Compatible with

Blind Gift

eSUN Resin – White

3D CMYK Pigment Set for 3D Printer Resins – 4 X 30MLS

eSun ABS LIKE HARD TOUGH Resin for LCD/DLP 3D Printing

JAMGHE Glow In Dark 3D Printer Resin

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA

JAMGHE 10K Water Washable

Technical Specification

Compatible with

Blind Gift

Related products

eSUN Resin – White

3D CMYK Pigment Set for 3D Printer Resins – 4 X 30MLS

eSun ABS LIKE HARD TOUGH Resin for LCD/DLP 3D Printing

JAMGHE Glow In Dark 3D Printer Resin