PolyLite ABS Yellow 1.75mm

Rated 5.00 out of 5 based on 1 customer rating

$44.90

PolyLite™ ABS is made with a specialty bulk-polymerized ABS resin, which has significantly lower volatile content compared to traditional ABS resins. It delivers excellent printing quality with minimal odor during printing.

1kg - Yellow

In stock

Features:

Less Odor / Excellent Quality – PolyLite™ ABS is made with a specialty bulk-polymerized ABS resin, which has significantly lower volatile content compared to traditional ABS resins. It delivers excellent printing quality with minimal odor during printing.

Balanced Mechanical / Thermal Properties – PolyLite™ ABS features well balanced mechanical and thermal properties, outperforming regular PLA and PETG in toughness and featuring a heat resistance up to 100°C.

Affordable Technology – Polymakers industry leading filament quality and technology now available at an affordable price

Uncompromised Quality – With Polymaker’s industry leading quality control process and rigorous in-house testing, you can rest assured that PolyLite™ ABS will produce beautiful, reliable and accurate printed parts.

Can PolyLite™ ABS be post-processed with Acetone?
Yes, PolyLite™ ABS can be smoothed with acetone.
WARNING: Acetone is a dangerous chemical, please handle it with the necessary safety precautions.

Printing and Drying Settings:

Printing Temperature: 245˚C – 265˚C
Bed Temperature: 90˚C – 100˚C
Printing Speed: 30mm/s – 50mm/s
Fan: OFF

Direct Drive:
Retraction Distance: 1mm
Retraction Speed: 20mm/s
Indirect Drive:
Retraction Distance: 3mm
Retraction Speed: 40mm/s

Drying Settings: 70˚C for 6h
(Only if the material has absorbed moisture)

Weight	1 kg
Dimensions	20 × 20 × 6 cm
Brand	Polymaker
Colour	Yellow

1 review for PolyLite ABS Yellow 1.75mm

m*********
Rated 5 out of 5
May 18, 2023
Perfect Filament to use.
The BEST ABS filament I’ve ever used. This just lays down like butter. So easy to print & the finish is 5 stars. Service from 3Dea is 5 Stars as...More
The BEST ABS filament I’ve ever used. This just lays down like butter. So easy to print & the finish is 5 stars.
Service from 3Dea is 5 Stars as well.
Thanks Very much.
Helpful? 0 0

Add a review

Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less

Andrew Jackson

5

I was directed to 3D... Read More
I was directed to 3DEA by a work colleague as I was new to 3D printing and they were right about them. Great quality PLA (and many other types), awesome range of colours and great pricing. I've bought 4 different rolls so far and they have all been great, no clogging and brilliant print quality. Read Less

Greedo Twerp

5

I was looking for a ... Read More
I was looking for a colour similar to the primer red seen on German WW2 heavy vehicles. Wanted to print a 1/4 scale model of a Tiger tank 88mm muzzle brake. Ordered the 3DEA "Brick Red" PLA which is a very good match. Never used prior and pleased to report printed faultlessly once I knocked the temp down to 200 degrees on my Kingroon KP3S. Printed at 0.10mm layer height, no stringing issues at all. Very happy customer. Already planning the next order, highly recommended. Read Less

Write a review!

PolyLite ABS Yellow 1.75mm

Features:

1 review for PolyLite ABS Yellow 1.75mm

PolyLite ABS Black 2.85mm

ABS – Green 1.75mm

eSUN eABS Max 3D Filament 1.75mm

ABS – Orange 1.75mm

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA

PolyLite ABS Yellow 1.75mm

Features:

1 review for PolyLite ABS Yellow 1.75mm

Related products

PolyLite ABS Black 2.85mm

ABS – Green 1.75mm

eSUN eABS Max 3D Filament 1.75mm

ABS – Orange 1.75mm